Manual.ly Logo

Mafell KSS 80 Ec 370 Manuale

0,0 · 0 Valutazioni

Manuale PDF · 114 Pagine

Italiano

M: OA-GPT-5-NAN
pagina

/ 114

Loading...
be2c959cc8ef5dc27456ded27bfc0686d481 page 18
-24-
- Do not use dull or damaged blades.
Unsharpened or improperly set blades produce
narrow kerf causing excessive friction, blade
binding and kickback.
- Blade depth and bevel adjusting locking levers
must be tight and secure before making the
cut. If blade adjustment shifts while cutting, it may
cause binding and kickback..
- Use extra caution when sawing into existing
walls or other blind areas. The protruding blade
may cut objects that can cause kickback.
Lower guard function
- Check the lower guard for proper closing
before each use. Do not operate the saw if the
lower guard does not move freely and close
instantly. Never clamp or tie the lower guard
into the open position. If the saw is accidentally
dropped, the lower guard may be bent. Raise the
lower guard with the retracting handle and make
sure it moves freely and does not touch the blade
or any other part, in all angles and depths of cut.
- Check the operation of the lower guard spring.
If the guard and the spring are not operating
properly, they must be serviced before use.
Lower guard may operate sluggishly due to
damaged parts, gummy deposits, or a build-up of
debris.
- The lower guard may be retracted manually
only for special cuts such as "plunge cuts" and
"compound cuts". Raise the lower guard by the
retracting handle and as soon as the blade
enters the material, the lower guard must be
released. For all other sawing, the lower guard
should operate automatically.
- Always observe that the lower guard is
covering the blade before placing the saw
down on bench or floor. An unprotected,
coasting blade will cause the saw to walk
backwards, cutting whatever is in its path. Be
aware of the time it takes for the blade to stop after
switch is released.
Riving knife function
- Use the appropriate saw blade for the riving
knife. For the riving knife to function, the body of
the blade must be thinner than the riving knife and
the cutting width of the blade must be wider than
the thickness of the riving knife.
- Adjust the riving knife as described in this
instruction manual. Incorrect spacing, positioning
and alignment can make the riving knife ineffective
in preventing kickback.
- Always use the riving knife except when
plunge cutting. The riving knife must be replaced
after plunge cutting. The riving knife causes
interference during plunge cutting and can create
kickback.
- For the riving knife to work, it must be engaged
in the workpiece. The riving knife is ineffective in
preventing kickback during short cuts.
- Do not operate the saw if the riving knife is
bent Even a light interference can slow the closing
rate of a guard.
Instructions on service and maintenance:
- Regularly cleaning the machine, especially the
adjusting devices and guides, constitutes an
important safety factor.
- Only original MAFELL spare parts and accessories
may be used. Otherwise the manufacturer will not
accept any warranty claims and cannot be held
liable.
4 Setting / Adjustment
4.1 Mains connection
Prior to commissioning make sure that the mains
voltage complies with the operating voltage stated on
the machine's rating plate.
4.2 Chip extraction
Danger
Substances that are harmful to
health must be taken up with an M-
suction device.
Connect the machine to a suitable external dust
extractor during all work generating a considerable

Chatta con il manuale del tuo Mafell KSS 80 Ec 370 utilizzando l'IA

Ottieni risposte istantanee dall'IA dal manuale del tuo Mafell KSS 80 Ec 370

Chiedi qualsiasi cosa sul Mafell KSS 80 Ec 370. Le risposte provengono da questo manuale, con le pagine di riferimento.

KSS 80 Ec 370 Programma di manutenzione

Dopo un lungo periodo di utilizzo
Ispezione professionale da parte di un servizio autorizzato

Consegnare la macchina a un centro assistenza clienti MAFELL autorizzato per l'ispezione dopo un lungo periodo di funzionamento.

Mostra nel manuale (pagina 16)
Prima di ogni utilizzo
Verificare il funzionamento della protezione inferiore

Assicurarsi che la protezione inferiore si chiuda correttamente e si muova liberamente; non utilizzare se rimane bloccata o è danneggiata.

Mostra nel manuale (pagina 24)
Regolarmente
Pulire i dispositivi di regolazione e le guide

La pulizia regolare della macchina, in particolare dei dispositivi di regolazione e delle guide, è un importante fattore di sicurezza.

Mostra nel manuale (pagina 13)
M: QW-35-FL

Fai una Domanda

0/1000

Consigli KSS 80 Ec 370?

Sì No

Domande frequenti

A

The saw uses 237 mm diameter carbide-tipped blades with a 30 mm bore. Recommended tooth counts: 12T for rip, 24T for general rip/cross cuts, and 56T for fine cross cuts. Use only blades rated for the saw’s idle speed and EN 847-1 compliant.

Questa risposta è utile?

A

Cutting depth is continuously adjustable up to 88 mm (varies with tilt). The saw unit tilts from 0° to 60° for bevel cuts. For the KSS80Ec 370 in cross-cut configuration, effective cutting depths are slightly reduced (e.g., 82/69/55/38 mm at 0°/30°/45°/60°).

Questa risposta è utile?

A

Yes: harmful dusts must be extracted with an M-class extractor for prolonged work. The saw’s extraction port diameter is 35 mm and requires an external extractor capable of at least 20 m/s air velocity for effective removal.

Questa risposta è utile?

A

The saw includes a riving knife/splitter, upper fixed and lower retractable guards, a large base plate, handles for two-handed control, electronic motor management with overload protection, and an automatic brake. Proper blade choice, secure work support and using the riving knife (except for plunge cuts) also reduce kickback risk.

Questa risposta è utile?

A

The KSS80Ec 370 uses a 2300 W universal motor (available for other voltages in some regions). Built-in electronics ensure smooth acceleration, regulate speed under load, and reduce motor output on overload; an automatic brake limits blade coast time to about five seconds.

Questa risposta è utile?

A

Yes. The saw handles panel materials like chipboard and MDF when using appropriate blades. Mafell offers guide rails (F80–F310) and accessories to enable accurate guided and long cuts; specialized guide and rail kits increase precision and convenience.

Questa risposta è utile?

A

Keep adjustment mechanisms and guides clean of debris, inspect the lower guard and spring, replace worn blades and brushes as needed, and use Mafell-specified grease for lubrication points. For long-term service, have the machine inspected at an authorized Mafell service workshop.

Questa risposta è utile?

M: OA-GPT-5-NAN

Vantaggi e Svantaggi

Vantaggi

  • High power 2300 W motor with stepless speed control (2250–4400 rpm) for versatile cutting.
  • Comprehensive safety set: upper/lower guards, riving knife, brake and robust base plate.
  • Precise plunge and bevel capability (0°–60°) with adjustable cutting depth up to 88 mm.
  • Compatible with Mafell guide rails and accessories for long, accurate guided cuts.
  • Solid build and low-maintenance design with lifetime-lubricated bearings.
VS

Svantaggi

  • High noise emission (LPA 91 dB(A), LWA 102 dB(A)) requires hearing protection.
  • Weight increases significantly with guiding device (up to ~8.3 kg), affecting portability.
  • Requires correct blade selection and maintenance; improper blades risk kickback or damage.
  • Dust extraction mandatory for health; needs M-class extractor for heavy dust loads.
  • Replacement parts and specialized grease recommended from manufacturer to retain warranty.
M: OA-GPT-5-NAN

Prodotto Specifiche

Tipo

Sega circolare

Potenza

2300W

Velocita' a vuoto

2250-4400/min

Diametro lama della sega

237mm

Capacita' di taglio

82mm (profondita' di taglio a 0 gradi), 55,5mm (profondita' di taglio con inclinazione di 45 gradi)

Inclinazione lama

0-60 gradi

Portautensile

Foro 30mm

Caratteristiche speciali

Controllo velocita', Guida parallela, Estrazione polvere, Protezione da sovraccarico, Funzione di inclinazione

Peso

8,30kg

M: GO-GEM-FL-25

Descrizione del prodotto Descrizione

Mafell KSS80Ec 370 Electric Hand Circular Saw — Powerful Precision for Professionals

The Mafell KSS80Ec 370 Electric Hand Circular Saw is a robust, professional-grade portable circular saw and cross-cutting system engineered for demanding woodworking tasks. With a 2,300 W universal motor and stepless speed control from 2,250 to 4,400 rpm, it delivers consistent cutting performance across hardwood, softwood and engineered panels. The KSS80Ec 370 variant adds a guiding assembly to expand cutting length (370 mm at 80 mm workpiece thickness) and enhance accuracy for rip and cross cuts.

Designed for tradespeople and serious hobbyists, the saw emphasizes safety and usability. It includes upper and retractable lower guards, a riving knife/splitter, a built-in brake, and a large base plate for stability. The electronic motor management ensures smooth acceleration and overload protection; an automatic brake reduces blade coast time to about five seconds. The machine accepts 237 mm carbide-tipped blades (30 mm bore) and ships with a 12-tooth blade, riving knife, parallel guide and service tool depending on model configuration.

Versatility is a core strength: plunge cuts, bevel cuts from 0°–60°, and adjustable cutting depths up to 88 mm (varying with tilt) are supported. The saw’s bevel and depth scales, plunge-latch mechanism and adjustable riving knife make repetitive and precise operations straightforward. Dust management is addressed with a 35 mm extraction port; users are advised to connect an M-class extractor for health protection during heavy dust generation.

Technical highlights include clear specifications for cutting depths and blade sizes, robust safety devices, and optional guide rails (F80–F310) and accessories to expand capability. The manual provides step-by-step procedures for blade changes, setting the riving knife, using the parallel or roller edge guides, and troubleshooting common faults. Emission data (LPA 91 dB(A), LWA 102 dB(A)) and vibration (<2.5 m/s2) are stated, so users can plan PPE and jobsite measures accordingly.

With careful adherence to safety instructions (use of hearing and dust protection, correct blade selection, secure clamping of workpieces), the KSS80Ec 370 offers controlled, accurate cuts and dependable durability in professional environments.

Notes

  • Use only approved blades (EN 847-1) with correct bore and dimensions; avoid damaged or HSS blades.
  • Always connect adequate dust extraction (air velocity ≥ 20 m/s) for prolonged work.
  • Regularly clean adjustments and guides; use original Mafell spare parts and grease as specified.
M: OA-GPT-5-NAN

© Copyright 2026 Manual.ly