Manual.ly Logo

Benning MM 5-1 Manuale

0,0 · 0 Valutazioni

Manuale PDF · 137 Pagine

Italiano

M: QW-35-FL
pagina

/ 137

Loading...
109c1933695fa1714032b8c4405a5d0ae7d5 page 1d
02/ 2020
BENNING MM 5-1/ 5-2
29
In these cases, the BENNING MM 5-1/ MM 5-2 must be switched off immediately,
removed from the measuring points and secured to prevent it from being used again.
9.2 Cleaning
Clean the outside of the unit with a clean dry cloth. (Exception: any type of
special cleaning cloth). Never use solvents or abrasives to clean the testing unit.
Ensure that the battery compartment and the battery contacts have not been
contaminated by electrolyte leakage.
If any electrolyte or white deposits are seen near to the battery or in the battery
compartment, remove them with a dry cloth, too.
9.3 Battery replacement
Before opening the BENNING MM 5-1/ MM 5-2, ensure that it is
not connected to a source of voltage! Electrical hazard!
The BENNING MM 5-1/ MM 5-2 is supplied by means of two integrated 1.5 V
micro (AAA) batteries. Battery replacement (see figure 13) is required as soon
as all segments of the battery symbol
3
have disappeared and the battery
symbol is flashing.
To replace the battery, proceed as follows:
- First remove the safety measuring leads from the measurement circuit.
- Remove the safety measuring leads from the BENNING MM 5-1/ MM 5-2.
- Turn the rotating switch
to “OFF”.
- Remove the protective rubber holster
M
from the BENNING MM 5-1/ MM 5-2.
- Lay the BENNING MM 5-1/ MM 5-2 on its front and loosen the screw from
the cover of the battery compartment.
- Lift off the battery compartment cover from the bottom part of the battery
compartment.
- Remove the discharged batteries from the battery compartment.
- Insert the new batteries into the battery compartment observing correct
po larity.
- Clip the battery cover onto the bottom part and tighten the screw.
- Replace the BENNING MM 5-1/ MM 5-2 in its protective rubber holster
M
.
See fig. 13: Battery replacement
Remember the environment! Do not dispose of used batteries
with domestic waste. Dispose of them at a battery-collection
point or as toxic waste. Your local authority will give you the
information you need.
9.4 Fuse replacement (BENNING MM 5-2)
Before opening the BENNING MM 5-2, ensure that it is not
connected to a source of voltage! Electrical hazard!
The BENNING MM 5-2 is protected against overload by means of an inte grated
fuse (G melt insert) 15 A rapid (see figure 14). Proceed as follows to replace
the fuse:
- Disconnect the safety measuring leads from the measurement circuit.
- Disconnect the safety measuring leads from the BENNING MM 5-2.
- Turn the rotating switch
to the “OFF” position.
- Remove the protective rubber holster
M
from the BENNING MM 5-2.
- Lay the BENNING MM 5-2 on its front and loosen the screw from the cover
of the battery compartment.
- Lift off the battery compartment cover from the bottom part of the battery
compartment.
Do not loosen any of the screws on the printed circuit of the
BENNING MM 5-2!
- Remove the four outer screws (black) from the bottom part of the housing.
- Lift the housing base at the bottom and remove it from the top of the front part.
- Lift one end of the defective fuse out of the fuse holder.
- Push the defective fuse out of the fuse holder completely.
- Replace the defective fuse with another of the same rated power, same trig-
gering characteristics and same dimensions.
- Push the new fuse into the centre of the holder.
- Clip the housing base into the front part and replace the four screws.
- Clip the battery cover onto the bottom part and tighten the screw.
- Replace the BENNING MM 5-2 in its protective rubber holster
M
.
See fig. 14: Fuse replacement

Chatta con il manuale del tuo Benning MM 5-1 utilizzando l'IA

Ottieni risposte istantanee dall'IA dal manuale del tuo Benning MM 5-1

Chiedi qualsiasi cosa sul Benning MM 5-1. Le risposte provengono da questo manuale, con le pagine di riferimento.

MM 5-1 Programma di manutenzione

Ricordami quando e' necessaria la manutenzione
Annuale
Calibrare il dispositivo presso l'assistenza in fabbrica

Inviare lo strumento al Centro Assistenza Benning per la ricalibrazione per mantenere la precisione specificata. L'intervallo consigliato e di un anno.

Mostra nel manuale (pagina 30)
Regolarmente
Pulire l'esterno dell'involucro

Pulire l'esterno dell'unita con un panno pulito e asciutto. Non utilizzare solventi o abrasivi.

Mostra nel manuale (pagina 29)

Promemoria di manutenzione gratuiti

In base alla data di acquisto. Sempre gratuito, annulla l'iscrizione in qualsiasi momento.

Inviando, accetti l'informativa sulla privacy. Puoi annullare l'iscrizione con un clic in qualsiasi email.
M: qwen/qwen3.8-flash

Fai una Domanda

0/1000

Consigli MM 5-1?

Sì No

Domande frequenti

A

El Benning MM 5-1 puede medir con seguridad voltajes de hasta 600 V DC o AC en circuitos de Categoría III y hasta 300 V en circuitos de Categoría IV en relación a tierra.

Questa risposta è utile?

A

No, el modelo Benning MM 5-1 no tiene capacidades integradas de medición de temperatura. Esta característica está disponible en el modelo Benning MM 5-2 que soporta un termopar tipo K.

Questa risposta è utile?

A

Apague el dispositivo, retire la funda de goma, destornille la tapa trasera, saque las baterías viejas, inserte nuevas baterías micro de 1.5 V con la polaridad correcta y vuelva a ensamblar la unidad.

Questa risposta è utile?

A

La función VoltSensor le permite detectar la presencia de voltaje AC contra tierra sin hacer contacto físico, indicado por un LED rojo y un símbolo en la pantalla.

Questa risposta è utile?

A

No, el dispositivo está diseñado estrictamente para entornos secos. Usarlo en condiciones húmedas o alta humedad puede comprometer la seguridad y la precisión.

Questa risposta è utile?

A

Benning recomienda recalibrar el dispositivo cada año para mantener la precisión de medición especificada y el cumplimiento con las especificaciones técnicas.

Questa risposta è utile?

M: QW-35-FL

Vantaggi e Svantaggi

Vantaggi

  • Tecnología de medición True RMS para lecturas precisas en señales no sinusoidales
  • La función VoltSensor permite la detección de voltaje AC sin contacto
  • Diseño durable con funda de goma protectora y soporte magnético
  • Smart HOLD y almacenamiento de valor pico para capturar datos transitorios
  • Cumple con estándares de seguridad CAT III 600V y CAT IV 300V
VS

Svantaggi

  • La vida útil de la batería puede disminuir significativamente en temperaturas frías
  • Sin medición de temperatura integrada (requiere sensor separado)
  • No puede medir frecuencia en entradas de corriente sin configuración específica
  • Requiere reemplazo manual de fusible para protección contra sobrecarga
  • Limitado a entornos secos únicamente, sin resistencia al agua
M: QW-35-FL

Prodotto Specifiche

Intervallo di misura

max. 600 V, max. 100 MΩ

Contenuto della confezione

Borsa

M: QW-35-FL

Descrizione del prodotto Descrizione

El Multímetro Benning MM 5-1: Precisión y Seguridad en Cada Medición

El multímetro Benning MM 5-1 se destaca como una herramienta confiable para electricistas e individuos técnicamente capacitados que requieren diagnósticos precisos en entornos secos. Diseñado con la seguridad como prioridad, este dispositivo soporta mediciones de hasta 600 V DC/AC, cumpliendo con las estrictas categorías de sobretensión III y IV. Su construcción robusta incluye una funda de goma protectora que no solo protege la unidad de daños mecánicos sino que también cuenta con un imán integrado para operación sin manos y un soporte para una lectura más fácil.

Este multímetro digital ofrece una amplia gama de funciones incluyendo voltaje directo, voltaje alterno, resistencia, prueba de diodos y verificaciones de continuidad con zumbador audible. La gran pantalla LCD de 4 dígitos asegura una visibilidad clara de las lecturas, mientras que funciones como Smart HOLD y almacenamiento de valor pico permiten a los usuarios capturar datos transitorios sin esfuerzo. La inclusión de la función VoltSensor permite la detección sin contacto de voltajes AC contra tierra, añadiendo una capa de conveniencia y seguridad durante tareas de identificación de fase. Con una tasa de medición de dos por segundo y selección automática de rango, el Benning MM 5-1 simplifica el complejo diagnóstico eléctrico en un proceso fluido.

Para alimentar el dispositivo hay dos baterías micro estándar de 1.5 V, proporcionando aproximadamente 300 horas de uso continuo. La unidad está equipada con un indicador de batería que alerta a los usuarios cuando es necesaria la reemplazo, previniendo lecturas inexactas debido a la energía baja. Ya sea verificando circuitos, probando componentes o diagnosticando fallas, el Benning MM 5-1 ofrece un rendimiento constante respaldado por una garantía de calibración de un año del fabricante.

Resumen de Características Clave

El Benning MM 5-1 combina durabilidad con funcionalidad avanzada. Su tecnología True RMS asegura lecturas precisas incluso en formas de onda no sinusoidales dentro de límites especificados. El dispositivo cumple con las directivas de la UE y cuenta con doble aislamiento para mayor protección del usuario. El mantenimiento es sencillo, con acceso fácil para el reemplazo de baterías y fusibles, asegurando confiabilidad a largo plazo en entornos profesionales.

Notas Importantes

Siempre asegúrese de que el dispositivo esté desenergizado antes de abrirlo para mantenimiento. Los imanes dentro de la unidad pueden afectar a los marcapasos, así que mantenga una distancia segura si tiene tales implantes médicos. No use el dispositivo en condiciones húmedas o más allá de sus límites de voltaje rated.

M: QW-35-FL

© Copyright 2026 Manual.ly