Manual.ly Logo

sera UVC-Xtreme 800 Manuale

0,0 · 0 Valutazioni

Manuale PDF · 90 Pagine

Italiano

M: GO-GEM-FL-25
pagina

/ 90

Loading...
781d6a9054693a344975a2f7322d15035812 page 11
17
Maintenance and care
Cleaning (every 4 – 12 weeks)
Over time and depending on biological load, food amount and aquarium
volume, mechanical and biological lter media get clogged more or less
quickly. Due to increasing sedimentation, the turnover through the lter
is reduced.
For cleaning, please rst pull the barrel plug from the lter head (6.5)
and then close the valves by turning the taps by 90° perpendicular to
the ow direction (6.4).
Now open the 4 holder clips (8.1 – 8.2). This leads to pressure release,
and you can now unscrew the valves from the lter head without water
running out (7.6). Now take the lter head off and lay it aside, or put it
back if you wish to carry it to a sink or the location where you wish to
clean the lter media.
You can now take the lter media baskets (1.34) out from above and
wash out the lter materials. It is best to use aquarium water for wash-
ing them out since this, unlike tap water, does not endanger the lter
bacteria. Never replace the lter material entirely but always retain used
lter material. By doing so, the lter bacteria will then spread over the
entire lter material again. Newly setup lters can also be activated by
using used lter material.
Maintenance of the running unit (every 3 – 9 months)
Please check the bottom side of the lter head whether the running unit
can move freely. To do so, please remove the two 90° elbows and the
pump chamber cover. Turn the rotor with your ngers. You should be able
to turn it without suspicious resistance. Rinse the openings thoroughly
with a water beam, depending on deposits and biolm, and re-assemble
the lter (4.1 – 4.7).
Possible problem sources and solution
Problem Possible cause Possible solution
E1 Suction pump does not ll up the
lter
E1.1 Are “IN” and “OUT” valves/hoses mixed up?
Check if bubbles are coming out of the intake strainer while suction
pump is in operation.
Yes, switch “IN” and “OUT” valves/hoses.
Make sure that the valve marking corresponds with the valve connector marking
(7.3).
No, see item E1.2
E1.2 Are “IN”/“OUT” valves still closed? Yes, open taps (6.4) of the “IN”/“OUT” valves.
No, see item E1.3
E1.3 Did you forget to insert the lter head seal (1.31)?
Yes, insert the lter head seal.
No, see item E1.4
E1.4
Are hoses laid out in a loop?
Yes, lay the hoses out without loops, shorten them if applicable.
No, see item E1.5
E1.5 Is the lter in operation for the rst time? Yes, ll the lter canister with water by two thirds. Then press “S”.
No, see item E1.6
E1.6
Dirt particles in the outlet valve?
Yes, remove the valve, clean it, and re-assemble.
No, see item E1.7
E1.7 Too low water level of the tank (e.g. terrapin tank)? Yes, press “S” button (2) repeatedly after suction is completed, or raise the
performance setting by pressing the “+” button. The setting can be adjusted as
desired once the air trapped inside the lter has escaped.
No, see item E1.8
E1.8 Is the spray bar too deep underneath the water surface? Yes, install the spray bar parallel to water surface, 15 cm (6 in.) underneath it at the
maximum (7.1).
No, see item E5, or please contact your retailer.
E2 Pump does not work E2.1 Power supply interrupted? Check mains and 5.5 mm (0.2 in.) barrel
plugs.
Yes, connect to power supply.
No, see item E2.2
E2.2 Are the valves still closed? Yes, open valve taps (6.4).
No, see item E2.3
E2.3 Is the rst LED ashing (green)? Yes, exit standby mode by pressing the “+” button (2).
No, see item E2.4
E2.4 Are the rst and second green LEDs ashing at the same time? Yes,
– disconnect the lter from the mains supply and reconnect it; or
– disconnect the lter from the mains supply, open the lter head (8.1 – 8.2). Clean
the lter head, in particular the rotor (3), so the rotor can rotate freely.
No, see item E2.5
E2.5 Too much air in lter? Yes, see item E5 of the chart.
No, please contact your retailer.
E3 Pump performance has strongly
decreased
E3.1 Are the valve taps (6.4) not in the correct “OPEN” position? Yes, open the valve taps properly so both handles are parallel to the longitudinal axis
of the valves.
No, see item E3.2
E3.2 Hoses bent, polluted or covered with biolm layers? Is there an
obstacle in the tubing?
Yes, clean/brush hoses and tubing, remove biolm inside the hoses by means of a
hose brush. Remove obstacles in the tubing.
No, see item E3.3
E3.3 Intake strainer or outlet clogged? Yes, clean strainer or outlet and remove coarse dirt.
No, see item E3.4
E3.4 Too much air trapped inside the lter? Yes, press “S” key (2) until pump works properly, repeat as required.
No, see item E3.5
E3.5 Too many devices connected to lter? Yes, prelters, T pieces, UV-C lamps etc. additionally connected to the intake or
outlet reduce the ow rate. The UVC-Xtreme lter already contains a suitable UV-C
lamp.
No, see item E3.6
Replacing the UV-C lamp (every 1 – 1.5 years)
Should the blue LED indicator lamp stay off, or if the UV-C lamp is
1.5 years old at the maximum, it needs to be replaced. First switch off
the lter head for replacing the lamp. Pull the barrel plug from the lter
head (6.5). Then you can disconnect the head from the lter (8.1 – 8.2).
Unscrew the union nut of the UV-C intake nozzle after having removed
the magnetic contact (1.18, 9.1/9.2), then pull the two 90° elbows at-
tached to the nozzles (9.3).
Now the union nut of the UV-C nozzle can be unscrewed (9.4). Pull the
nozzle off upwards. The quartz glass cylinder is located underneath.
It can now be pulled off, granting access to the lamp (9.5). The UV-C
lamp can be removed from the socket by pulling it gently. It can now be
replaced with a suitable replacement lamp. Then re-assemble the lter
in reverse order (9.6 – 9.1).
Switch-off protection: UV-C radiation is dangerous. Irradiation of
eyes and skin must be strictly avoided. The lters are constructed
according to latest safety standards in a way that a magnetic switch
switches off the UV-C lamp as soon as the lamp casing is opened.
Prior to every maintenance measure, the magnetic contact should
be removed rst before removing the two clickable 90° elbows, as
this will prevent possible eye or skin damage caused by UV-C radia-
tion being released from the now opened connection of the two 90°
elbows at the UV-C tube, in case disconnecting the device from the
mains supply was forgotten.
000000-00_sera UVC Xtreme 800_1200_INT_GBI.indd 17 07.09.2017 08:12:35

Chatta con il manuale del tuo sera UVC-Xtreme 800 utilizzando l'IA

Ottieni risposte istantanee dall'IA dal manuale del tuo sera UVC-Xtreme 800

Chiedi qualsiasi cosa sul sera UVC-Xtreme 800. Le risposte provengono da questo manuale, con le pagine di riferimento.

UVC-Xtreme 800 Programma di manutenzione

Ricordami quando e' necessaria la manutenzione
Ogni 4 settimane
Pulire il materiale del filtro

Lavare i materiali meccanici e biologici del filtro utilizzando l'acqua dell'acquario per preservare i batteri. Non sostituire tutto il materiale contemporaneamente.

Mostra nel manuale (pagina 17)
Ogni 6 mesi
Manutenzione dell'unità in funzione

Verificare se il rotore ruota liberamente a mano e risciacquare le aperture con un getto d'acqua per rimuovere biofilm o depositi.

Mostra nel manuale (pagina 17)
Ogni 9 mesi
Sostituire la lampada UV-C

Cambiare la lampada al mercurio dopo un massimo di 1,5 anni per garantire il pieno funzionamento, anche se la spia luminosa è ancora accesa.

Mostra nel manuale (pagina 17)

Promemoria di manutenzione gratuiti

In base alla data di acquisto. Sempre gratuito, annulla l'iscrizione in qualsiasi momento.

Inviando, accetti l'informativa sulla privacy. Puoi annullare l'iscrizione con un clic in qualsiasi email.
M: QW-35-FL

Fai una Domanda

0/1000

Consigli UVC-Xtreme 800?

Sì No

Domande frequenti

A

Unit UV-C dimaksudkan untuk mengurangi patogen dan alga mengambang dengan menyinari air setelah melewati media filter. Sistem ini tidak dirancang untuk mensterilkan akuarium, dan bakteri menguntungkan pada media sebagian besar tetap tidak terpengaruh.

Questa risposta è utile?

A

Mulai dengan tingkat kinerja sedang dan sesuaikan berdasarkan ukuran tangki Anda serta tekanan alga atau patogen. Sirkulasi yang lebih rendah meningkatkan waktu air berada di unit UV-C, yang dapat meningkatkan pengurangan. Jika ada udara yang terperangkap atau aliran tampak lemah, tingkatkan sebentar.

Questa risposta è utile?

A

Selama pengoperasian pertama, udara yang terperangkap dapat mencapai area rotor dan meningkatkan kebisingan. Gunakan fungsi pompa hisap untuk menghilangkan udara di bawah kepala filter. Setelah beberapa menit, kebisingan biasanya berkurang setelah aliran udara stabil.

Questa risposta è utile?

A

Media mekanis dan biologis harus diperiksa dan dibersihkan sekitar setiap 4 hingga 12 minggu, tergantung pada beban biologis, pemberian makan, dan volume akuarium. Jika sirkulasi berkurang, bersihkan hanya yang diperlukan dan hindari mengganti semua media sekaligus.

Questa risposta è utile?

A

Masa pakai lampu tergantung pada siklus pengaktifan, tetapi panduan servis menunjukkan sekitar 1 hingga 2 tahun. Lampu harus diganti setelah sekitar 1,5 tahun untuk memastikan kinerja penuh, terutama jika indikator UV-C tidak lagi menunjukkan operasi normal.

Questa risposta è utile?

A

Periksa apakah katup MASUK/KELUAR terbuka penuh, selang tidak tertekuk, dan keranjang media tidak tersumbat. Juga pastikan rotor dapat bergerak bebas dan tidak ada udara yang terperangkap berlebihan. Jika masalah berlanjut, periksa jalur keluaran dan hubungi pengecer.

Questa risposta è utile?

M: GO-GEM-FL-25

Vantaggi e Svantaggi

Vantaggi

  • UV-C terintegrasi yang dapat diaktifkan dengan lampu amalgam untuk kinerja yang stabil dan potensi emisi yang lebih tinggi
  • Motor tegangan rendah, rendah kebisingan dengan beberapa pengaturan untuk menyesuaikan aliran, penggunaan energi, dan waktu paparan UV
  • Pompa hisap listrik membantu membuang udara yang terperangkap setelah pemasangan atau pemeliharaan untuk operasi yang tenang
  • Katup yang dapat diputar 360 derajat dan kit koneksi lengkap menyederhanakan instalasi dan penanganan
  • Jalur aliran keranjang media yang dioptimalkan mendukung filtrasi mekanis dan biologis dengan interval servis yang panjang
VS

Svantaggi

  • Membutuhkan penanganan keamanan UV-C yang hati-hati dan hanya lampu amalgam pengganti asli
  • Kinerja menurun jika media filter atau selang tersumbat atau jika aliran udara terhalang
  • Penyegelan yang benar, penempatan tegak, dan koneksi MASUK/KELUAR yang tepat sangat penting untuk mencegah kebocoran dan masalah udara
  • Tugas servis (pemeliharaan rotor dan UV-C) melibatkan pembongkaran yang harus dilakukan dengan hati-hati
M: GO-GEM-FL-25

Prodotto Specifiche

Tipo

Filtro esterno con chiarificatore UV-C

Portata

840 l/h

Dimensioni acquario

100-800 l

Potenza assorbita

24 W

Caratteristiche

Lampada UV-C, incl. set ingresso/uscita

M: GO-GEM-FL-25

Descrizione del prodotto Descrizione

sera Professional UVC-Xtreme 800 Filter Eksternal

Filter Eksternal sera Professional UVC-Xtreme 800 menghadirkan dukungan UV-C dan kontrol elektronik ke dalam sistem filtrasi eksternal yang efisien dan rendah kebisingan, dibuat untuk akuarium air tawar. Dirancang untuk instalasi fleksibel, filter ini menggunakan motor tegangan rendah modern dengan beberapa tingkat kinerja, memungkinkan Anda menyesuaikan sirkulasi air dengan ukuran tangki, beban biologis, dan intensitas perawatan UV-C yang Anda inginkan. Dalam mode hemat energi, filter ini dapat berjalan dengan daya rendah sambil tetap memberikan sirkulasi yang kuat saat dibutuhkan.

Yang membedakan seri Xtreme adalah unit UV-C terintegrasi yang dapat diaktifkan dari panel kontrol. Lampu amalgam UV-C memberikan keluaran yang stabil dalam rentang suhu operasinya dan dimaksudkan untuk mengurangi patogen dan alga mengambang lebih efektif daripada banyak lampu UV-C konvensional. Daripada bertujuan untuk sterilisasi sejati, sistem ini berfokus pada pengurangan patogen sambil menjaga bakteri filter bermanfaat yang hidup terutama di media filter.

Air mengalir melalui keranjang media yang dioptimalkan dari atas ke bawah. Spons berlekuk membantu menangkap partikel kasar, sementara pilihan media halus dan biologis (misalnya, biomedia keramik) mendukung filtrasi mekanis dan biologis. Setelah melewati media, air yang telah diolah secara mekanis dan biologis ditarik ke zona UV-C, kemudian dikembalikan ke akuarium melalui katup KELUAR. Sistem ini juga mencakup pompa hisap listrik yang membantu menghilangkan udara yang terperangkap setelah pemasangan atau pemeliharaan, mendukung operasi yang tenang dan andal.

Untuk penggunaan yang aman dan benar, pertimbangkan Manual Filter Eksternal sera Professional UVC-Xtreme 800 saat mengatur ballast, memposisikan filter, dan menangani komponen UV-C. Unit ini dimaksudkan untuk penggunaan di dalam ruangan, membutuhkan aliran air yang cukup, dan mencakup langkah-langkah keamanan untuk mencegah paparan UV-C selama pemeliharaan.

Hasil utama

  • Filtrasi eksternal berkemampuan UV-C dengan kontrol yang dapat diaktifkan untuk mengurangi patogen dan alga mengambang
  • Beberapa tingkat kinerja motor untuk menyeimbangkan sirkulasi, waktu paparan UV, dan penggunaan energi
  • Rutinitas penghilangan udara terintegrasi untuk permulaan yang lebih lancar setelah pembersihan
  • Jalur aliran dan keranjang media yang dioptimalkan untuk mendukung interval servis yang panjang
  • Orientasi katup 360 derajat yang mudah dan kit koneksi yang disertakan untuk pengaturan yang fleksibel

Catatan

  • Utamakan pembersihan media sebagian dan penggunaan kembali media yang sudah mapan untuk melindungi bakteri menguntungkan.
  • Lampu amalgam UV-C biasanya diganti pada siklus servis (sekitar 1 hingga 2 tahun tergantung pada pengaktifan), mengikuti panduan unit.
  • Pastikan penyegelan yang tepat, penempatan tegak, dan pemasangan pipa MASUK/KELUAR yang benar untuk menjaga aliran dan efisiensi.
M: GO-GEM-FL-25

© Copyright 2026 Manual.ly