Manual.ly Logo

Nolan N100-5 Manuale

0,0 · 0 Valutazioni

Manuale PDF · 116 Pagine

Italiano

M: GO-GEM-FL-25
pagina

/ 116

Loading...
69fd6a5e58c38ca0373746be471a62d62d3f page 16
22
N100-5
8 CHEEK PAD ASSEMBLY
8.1 Put the left cheek pad against the corresponding polystyrene inner cheek pad,
insert the chin strap into the passageway of the cheek pad padding and push it
near the three buttons on its back in order to fasten them to their seats (Fig.15).
8.2 Repeat these steps with the right cheek pad padding.
Warning: the buttons are not fastened until a click is heard. Check that the strap
comes out properly from the cheek pad padding.
8.3 Insert the chin strap band into the elastic loops on the roll neck (Fig.14).
WARNING
- If your helmet is equipped with the double D-Ring retention system, pull it
down as indicated in the attached double D-Ring label.
- Remove the inner comfort padding only when cleaning or washing is required.
- Never use the helmet if the inner comfort padding and the cheek pads have not
been correctly and completely tted.
- Delicately hand-wash in lukewarm water (max. 30° C) and neutral soap.
- Rinse with cold water and allow drying at room temperature, away from direct
sunlight.
- Never machine-wash the inner comfort padding.
- The inner polystyrene is an easily deformable material. It is apt to change or get
partially destroyed to help absorb shocks.
- Do not modify or alter the helmet’s internal polystyrene components in any way.
- Clean the inner polystyrene components with a damp cloth only and allow it to dry
at room temperature away from direct sunlight.
- Never use tools or equipment of any sort to carry out the steps described above.
9 ADJUSTING THE ROLL NECK STRETCH
The roll neck stretch can be adjusted to adapt to the different sizes or riding positions
of the riders.
9.1 To increase the roll neck stretch press the button of the left strap clip and simulta-
neously pull the elastic strap towards the rear part of the helmet (Fig. 23). Follow
the same steps on the other side of the helmet.
9.2 To decrease the roll neck stretch press the button of the left strap clip button and
simultaneously push the rear part of the roll neck to loosen the stretch of the elas-
tic strap (Fig. 24). Follow the same steps on the other side of the helmet.
9.3 Wear and fasten the helmet (see instructions above) and make sure that the roll
neck stretch in the riding position is satisfactory.
WARNING
After assembling or disassembling the roll neck and/or adjusting the stretch, wear
and fasten the helmet to check the correct adjustment of the chin strap (see at-
tached label), the correct positioning of the helmet on the head in the riding posi-
tion and the VPS functionality in all positioning notches.
3.4 Pull the roll neck towards the inside of the helmet to remove the two rear aps
of the roll neck from the seats on the shell sealing edge and remove it from the
helmet (Fig.20).
4 LINER DISASSEMBLY
4.1 Unhook the left rear ap of the liner from the shell rear edge by slightly puling the
comfort padding towards the inside of the helmet (Fig.21). Follow the same steps
for the right rear ap.
4.2 Hold the left front part of the liner and pull it upwards in order to remove the cor-
responding liner ap from the support xed to the polystyrene inner shell (Fig.22).
Then repeat the same steps for the central front and right ap.
4.3 Completely remove the liner from the helmet.
5 LINER ASSEMBLY
5.1 Insert the liner correctly into the helmet and t it well against the base.
5.2 Insert the central front ap of the liner into its seat on the support xed to the pol-
ystyrene inner shell and push it downwards until it is completely locked (Fig.22).
Then repeat the operation with the left and right aps making sure that the side
ends of the liner are placed between the external side frames and the polystyrene
inner shell.
Warning: Check the correct assembly of the liner front area by lifting and lowering
the VPS. These movements should be smooth. If this is not the case, repeat steps
4.2 and 5.2.
5.3 Insert the rear right and left aps of the liner into the relevant lower seats on the
shell edge (Fig.21). Push the aps until they are fully hooked onto the support.
6 ASSEMBLY OF THE ROLL NECK
6.1 Insert the rear right and left aps of the roll neck into the relevant upper seats on
the shell edge (Fig.20). Push the aps until they are fully hooked onto the support.
6.2 Insert the side ap into the seat on the lining of the left polystyrene cheek pad and
push it towards the inside of the helmet until it is completely locked to the support
(Fig.19).
6.3 Press the front button of the roll neck to fasten it to the corresponding seat on the
lining of the left polystyrene cheek pad (Fig.18).
6.4 Follow the same steps on the other side of the helmet.
7 ASSEMBLY OF THE INNER EXPANDING FOAM PADDING OF THE CHEEK PADS
7.1 Gently put the inner expanding foam padding inside the fabric lining of the left
cheek pad (Fig.17). Carefully spread out the padding while checking that there are
no wrinkles in the cheek pad fabric lining.
7.2 Insert the upper ap “B” and the lower ap “C” of the frame into their loops on the
back of the frame (Fig.16).
7.3 Fasten the three eyelets “A” of the rear frame of the left cheek pad next to the three
snap buttons (top, front and rear) on its back (Fig.16).
7.4 Repeat these steps with the right cheek pad padding.
INSTRUCTIONS FOR USE

Chatta con il manuale del tuo Nolan N100-5 utilizzando l'IA

Ottieni risposte istantanee dall'IA dal manuale del tuo Nolan N100-5

Chiedi qualsiasi cosa sul Nolan N100-5. Le risposte provengono da questo manuale, con le pagine di riferimento.

N100-5 Programma di manutenzione

Dopo ogni utilizzo
Asciugare casco e visiera

Lasciare asciugare il casco in un luogo ventilato con la visiera aperta dopo l'uso. Tenere lontano da fonti di calore.

Mostra nel manuale (pagina 6)
Se necessario
Pulire la visiera interna PINLOCK

Rimuovere la visiera interna e pulirla delicatamente con sapone liquido neutro e panno umido. Sciacquare sotto acqua corrente.

Mostra nel manuale (pagina 6)
Periodicamente
Controllare l'allungamento PINLOCK

Controllare regolarmente l'allungamento corretto per prevenire movimenti e graffi delle superfici.

Mostra nel manuale (pagina 6)
Se necessario
Sostituire la visiera graffiata

Se la visiera è danneggiata o profondamente graffiata riducendo la visibilità, sostituirla immediatamente.

Mostra nel manuale (pagina 2)
Se necessario
Lavare l'imbotitura comfort

Lavare solo a mano in acqua tiepida (max 30 C) con sapone neutro. Non lavare in lavatrice.

Mostra nel manuale (pagina 22)
M: QW-35-FL

Fai una Domanda

0/1000

Consigli N100-5?

Sì No

Domande frequenti

A

È un casco modulare da moto con mentoniera ribaltabile, sistema visiera, protezione solare interna e funzioni orientate al comfort per l'uso quotidiano su strada.

Questa risposta è utile?

A

La finitura ad alta visibilità aiuta il motociclista a essere notato più facilmente nel traffico, cosa particolarmente utile in aree urbane trafficate, in condizioni di scarsa luce o con meteo variabile.

Questa risposta è utile?

A

La mentoniera utilizza un processo di apertura in due passaggi con leve separate di sgancio e apertura. Questo rende più facile l'uso con una sola mano e aiuta a ridurre le aperture accidentali.

Questa risposta è utile?

A

Sì. Il casco supporta una posizione di apertura minima della visiera per il flusso d'aria e può anche utilizzare una visiera interna Pinlock per migliorare la resistenza all'appannamento in condizioni umide o fredde.

Questa risposta è utile?

A

Sì. I guanciali, il paranuca e la fodera sono rimovibili, il che rende più facile la pulizia e aiuta a mantenere una vestibilità migliore e un interno più fresco nel tempo.

Questa risposta è utile?

A

Sì. Il casco è predisposto per i sistemi di comunicazione N-Com, a seconda della versione. Alcuni elementi interni in schiuma potrebbero dover essere rimossi durante l'installazione dei componenti compatibili.

Questa risposta è utile?

M: GO-GEM-FL-25

Vantaggi e Svantaggi

Vantaggi

  • La mentoniera Dual Action migliora la praticità e aiuta a prevenire aperture accidentali.
  • Il design ad alta visibilità aumenta la presenza del motociclista nel traffico e in condizioni di scarsa luce.
  • La visiera parasole VPS e il supporto opzionale Pinlock migliorano la visibilità con meteo variabile.
  • L'imbottitura rimovibile e il sistema di ventilazione migliorano il comfort e semplificano la manutenzione.
VS

Svantaggi

  • Il design modulare può sembrare più complesso di un semplice casco integrale.
  • Le parti della visiera, della VPS e del Pinlock richiedono una manipolazione attenta per evitare graffi o usura.
  • La protezione dipende dalla corretta vestibilità e da un fissaggio adeguato, quindi la taglia è molto importante.
  • Alcuni accessori e funzioni possono variare in base alla versione o richiedere un'installazione separata.
M: GO-GEM-FL-25

Prodotto Specifiche

Tipo

Casco Modulare

Caratteristiche

Visiera Parasole Integrata

Peso

1,65 kg

M: GO-GEM-FL-25

Descrizione del prodotto Descrizione

Nolan N100-5 Alta visibilità (varie taglie)

Il Nolan N100-5 Alta visibilità è progettato per i motociclisti che desiderano un casco modulare pratico, con grande attenzione a sicurezza, visibilità e comfort quotidiano. Pensato per l'uso in moto, combina una mentoniera ribaltabile, un sistema visiera trasparente e una finitura ad alta visibilità che aiuta il pilota a farsi notare più facilmente nel traffico. La sensazione generale è moderna, funzionale e adatta alla guida reale.

Una delle sue caratteristiche distintive è il sistema di mentoniera Dual Action. Questo meccanismo è progettato per essere aperto con una sola mano, aiutando al tempo stesso a ridurre il rischio di sgancio accidentale. I motociclisti possono passare da una configurazione completamente chiusa, per la massima protezione, a una configurazione aperta, per maggiore praticità nelle soste o nel traffico lento. Questa flessibilità rende il casco adatto sia ai pendolari sia ai turisti su due ruote.

La visibilità è un altro punto di forza importante. Il casco supporta una visiera esterna standard, una posizione di apertura minima per il flusso d'aria e l'antappannamento, e una visiera parasole interna VPS per condizioni di forte luminosità. Per i motociclisti che affrontano cambiamenti meteo, la visiera interna opzionale Pinlock aggiunge un ulteriore livello di supporto antiappannamento. Insieme, questi elementi aiutano a mantenere una visione più chiara della strada quando la temperatura scende, l'umidità aumenta o la luce solare diventa intensa.

Anche comfort e adattabilità ricevono grande attenzione. L'imbottitura interna rimovibile, i guanciali e le sezioni del paranuca sono realizzati per migliorare la vestibilità e semplificare la pulizia. Il sistema di ventilazione aiuta a convogliare aria fresca attraverso il casco, ridurre l'accumulo di calore e limitare l'appannamento della visiera. Inoltre, il casco è predisposto per i sistemi di comunicazione N-Com, diventando una scelta intelligente per i motociclisti che vogliono restare connessi senza compromettere il comfort.

Note

  • Più adatto ai motociclisti che cercano un casco modulare con grande versatilità nell'uso quotidiano.
  • Disponibile in varie taglie, quindi la vestibilità va controllata con attenzione per stabilità e comfort.
  • Seguire le indicazioni di pulizia e manutenzione per proteggere visiera, imbottitura e parasole.
  • Un controllo regolare di cinghie, componenti della visiera e sistemi di blocco aiuta a preservarne le prestazioni nel tempo.
  • Lo stile ad alta visibilità aggiunge un vantaggio pratico in termini di sicurezza nel traffico intenso e in condizioni di scarsa illuminazione.
M: GO-GEM-FL-25

© Copyright 2026 Manual.ly